Agilent Technologies G7104A Manuals

Manuals and User Guides for Agilent Technologies G7104A. We have 2 Agilent Technologies G7104A manuals available for free PDF download: User Manual

Agilent Technologies G7104A User Manual (310 pages)

Brand: Agilent Technologies | Category: Laboratory Equipment | Size: 34.34 MB

Table of Contents
5
1 Introduction

9
- Agilent 1260 Infinity II Flexible Pump
  
  10
  - Product Description
    10
  - Features
    11
- Agilent 1260 Infinity II Bio Flexible Pump
  
  12
  - Product Description
    12
  - Features
    13
- Operating Principle
  
  14
- Positions of the Multi Purpose Valve
  
  16
- Leak and Waste Handling
  
  20
  - Leak Sensor
    23
  - Waste Concept
    24
2 Site Requirements and Specifications

25
3 Using the Module

37
4 Preparing the Pump

84
- Capillary Coding Guide
  85
- Installing Capillaries
  88
5 How to Optimize the Performance of Your Module

92
6 Troubleshooting and Diagnostics

105
- User Interfaces
  106
- Agilent Lab Advisor Software
  107
- Pump Leak Rate Test
  108
- Troubleshooting the Pump Leak Rate Test
  111
- System Pressure Test
  113
- Pump Self Test
  115
7 Error Information

119
- What Are Error Messages
  121
- General Error Messages
  122
- Timeout
  122
- Shutdown
  123
- Remote Timeout
  124
- Lost CAN Partner
  124
- Leak Sensor Short
  125
- Leak Sensor Open
  126
- Compensation Sensor Open
  126
- Compensation Sensor Short
  127
- Fan Failed
  128
- Leak
  129
- Pump Error Messages
  130
- Pressure of Quaternary Pump above Upper Limit
  130
- Pressure below Lower Limit
  131
- Target Pressure Not Reached for Quaternary Pump Degasser
  131
- Solvent Counter Exceeded Limit
  132
- Waste Counter Limit Exceeded
  132
- Flow Rate Limit Exceeded
  133
- Quaternary Pump Shutdown During Analysis
  133
- Reading the Pump Encoder Tag Failed
  134
- Writing the Pump Encoder Tag Failed
  134
- Pump Drive Blocked or Encoder Failed
  135
- Drive Current too Low
  135
- Drive Current too High
  136
- Drive Timeout
  136
- Overcurrent of Pump Drive
  137
- Deliver Underrun
  137
- Defect Connection between Main Board and Pump Drive Encoder
  138
- Pump Drive Encoder Defect
  138
- Multipurpose Valve Failed
  138
- Reading of Multipurpose Valve Tag Failed
  139
- Pump Drive Encoder Rollover
  139
- Drive Position Limit
  139
- Insufficient Power of Drive Encoder LED
  140
- Drive Encoder Error
  140
- Writing the Multipurpose Valve Tag Failed
  140
- Unknown Multipurpose Valve Type
  141
- Pump Drive Encoder Error
  141
- Pump Drive Error
  141
- Maximum Stroke Is too Short
  142
- Pump Drive Stop Not Found
  142
- Timeout: Wait for Composition
  143
- Timeout: Wait for Run Volume
  143
- Timeout: Wait for Volume
  144
- Timeout: Wait for Flow
  144
- Timeout: Wait for Pressure
  145
- Drive Encoder Failed
  145
- Drive Phases Differ too Much in Electric Resistance
  146
- Degasser's Pressure Limit Violation
  146
- Seal Wash Pump was Missing When Tried to Turn on
  147
- Valve Hardware Overcurrent (MCGV)
  147
- Invalid Degasser Pressure Signal
  148
8 Maintenance

149
- Introduction to Maintenance
  151
- Warnings and Cautions
  153
- Overview of Maintenance
  154
- Cleaning the Module
  155
- Install Fittings and Capillaries
  156
- Remove and Install Doors
  157
- Replace the Pressure Sensor
  159
- Replace the Inlet Weaver
  161
- Replace the Inlet Valve (G7104C)
  163
- Replace the Inlet Valve (G7131C)
  164
- Remove the Jet Weaver
  165
- Install the Jet Weaver
  167
- Replace the Seal Wash Pump Cartridge
  169
- Replace the Multi-Channel Gradient Valve (MCGV)
  170
- Replace the Four-Channel Gradient Valve (4CGV)
  172
- Release a Stuck Inlet Valve
  174
- Remove the Pump Head Assembly (G7104C)
  176
- Remove the Pump Head Assembly (G7131C)
  178
- Pump Head Maintenance (Tool Free)
  181
- Disassemble Pump Heads (G7104C)
  182
- Disassemble Pump Heads (G7131C)
  186
- Replace the Heat Exchanger (G7104C)
  190
- Replace the Heat Exchanger (G7131C)
  192
- Assemble Pump Heads (G7104C)
  194
- Assemble Pump Heads (G7131C)
  200
- Install the Pump Head Assembly (G7104C)
  206
- Install the Pump Head Assembly (G7131C)
  208
- Replace the Outlet Valve (G7104C)
  210
- Replace the Outlet Valve (G7131C)
  213
- Replace the Multipurpose Valve
  215
- Replace Parts of the Multipurpose Valve (G7104C)
  217
- Replace Parts of the Multipurpose Valve (G7131C)
  218
- Replace the High Pressure Outlet Filter or Filter Frit
  219
- Install the Inline Filter
  221
- Remove the Inline Filter
  223
- Replace Parts of the Inline Filter
  224
- Replace the Seal Wash Sensor
  226
- Replace the Module Firmware
  228
- Prepare the Pump Module for Transport
  229
9 Parts and Materials for Maintenance

231
- Overview of Main Assemblies (G7104C)
  232
- Overview of Main Assemblies (G7131C)
  234
- Flow Connections (G7104C)
  236
- Flow Connections (G7131C)
  238
- Pump Heads (G7104C)
  240
- Pump Head Assembly Parts
  241
- Primary Pump Head Parts
  242
- Secondary Pump Head Parts
  243
- Pump Heads (G7131C)
  244
- Pump Head Assembly Parts
  244
- Primary Pump Head Parts
  245
- Secondary Pump Head Parts
  246
- Multipurpose Valve (G7104C)
  247
- Multipurpose Valve (G7131C)
  248
- Cover Parts
  249
- Accessory Kit (G7104C)
  250
- Accessory Kit (G7131C)
  251
- Tool Kit
  252
10 Identifying Cables

253
- Cable Overview
  254
- Analog Cables
  256
- Remote Cables
  258
- CAN/LAN Cables
  262
- Agilent Module to PC
  263
- USB Cables
  264
11 Hardware Information

265
- Firmware Description
  266
- Electrical Connections
  269
- Serial Number Information
  270
- Rear View of the Module
  270
- Interfaces
  271
- Overview Interfaces
  273
- USB (Universal Serial Bus)
  275
- Setting the 8-Bit Configuration Switch
  276
- Special Settings
  278
- Early Maintenance Feedback
  279
- Instrument Layout
  280
12 LAN Configuration What You Have to Do First

282
- TCP/IP Parameter Configuration
  283
- Configuration Switch
  284
- Initialization Mode Selection
  285
- Dynamic Host Configuration Protocol (DHCP)
  287
- General Information (DHCP)
  287
- Setup (DHCP)
  288
- Link Configuration Selection
  290
- Manual Configuration
  291
- With Telnet
  292
- PC and User Interface Software Setup
  296
- PC Setup for Local Configuration
  296
- User Interface Software Setup
  297
13 Appendix

298
- General Safety Information
  299
- Safety Standards
  299
- General
  299
- Before Applying Power
  300
- Ground the Instrument
  300
- Do Not Operate in an Explosive Atmosphere
  301
- Do Not Remove the Instrument Cover
  301
- Do Not Modify the Instrument
  301
- In Case of Damage
  301
- Solvents
  302
- Safety Symbols
  303
- Waste Electrical and Electronic Equipment Directive
  305
- Radio Interference
  306
- Sound Emission
  307
- Agilent Technologies on Internet
  308

Agilent Technologies G7104A User Manual (234 pages)

Flexible Pump

Brand: Agilent Technologies | Category: Water Pump | Size: 5.94 MB

Table of Contents

5
- 1 Introduction
  
  9
  - Product Description
    10
  - Features
    11
  - Operating Principle
    12
  - Positions of the Multi Purpose Valve
    14
  - Leak and Waste Handling
    19
- 2 Site Requirements and Specifications
  
  23
  - Site Requirements
    24
  - Physical Specifications
    27
  - Performance Specifications
    28
3 Using the Pump

31
- Magnets
  32
- Turn On/Off
  33
- Status Indicators
  34
- Best Practices
  35
4 How to Optimize the Performance of Your Module

39
6 Error Information

51
- What Are Error Messages
  53
- General Error Messages
  54
  - Timeout
    54
  - Shutdown
    54
  - Remote Timeout
    55
  - Lost CAN Partner
    56
  - Leak Sensor Short
    56
  - Leak Sensor Open
    57
  - Compensation Sensor Open
    57
  - Compensation Sensor Short
    58
  - Fan Failed
    59
  - Leak
    59
- Pump Error Messages
  60
7 Maintenance

79
- Introduction to Maintenance
  81
- Warnings and Cautions
  82
- Overview of Maintenance
  84
- Cleaning the Module
  85
- Install Fittings and Capillaries
  86
- Remove and Install Doors
  87
- Replace the Pressure Sensor
  88
- Replace the Inlet Weaver
  90
- Replace the Inlet Valve
  92
- Replace the Outlet Valve
  93
- Remove the Jet Weaver
  95
- Install the Jet Weaver
  97
- Replace the Seal Wash Pump
  99
- Replace the Multi-Channel Gradient Valve (MCGV)
  100
- Release a Stuck Inlet Valve
  102
- Pump Head Procedures
  104
  - Remove the Pump Head Assembly
    106
  - Disassemble the Pump Head Assembly
    108
  - Disassemble the Primary Pump Head
    111
  - Disassemble the Secondary Pump Head
    114
  - Replacing the Heat Exchanger
    117
  - Replace Wash Seal and Gasket
    120
  - Assemble the Primary and Secondary Pump Head
    122
  - Reassemble the Pump Head Assembly
    130
  - Install the Pump Head Assembly
    131
- Replace the Multi Purpose Valve
  133
- Replace Parts of the Multi Purpose Valve
  135
- Replace the High Pressure Outlet Filter or Filter Frit
  136
- Replace Parts of the Inline Filter
  138
- Replace the Module Firmware
  140
- Prepare the Pump Module for Transport
  141
8 Parts and Materials

143
- Overview of Main Assemblies
  144
- Flow Connections
  146
- Pump Head Assembly Parts
  148
- Primary Pump Head Parts
  150
- Secondary Pump Head Parts
  152
- Multi Purpose Valve
  154
- Cover Parts
  155
- Accessory Kit
  156
- Tool Kit
  157
- Tools
  158
- 9 Identifying Cables
  161
  - Cable Overview
    162
  - Analog Cables
    164
  - Remote Cables
    166
  - CAN/LAN Cables
    170
  - Agilent Module to PC
    171
  - USB Cables
    172
10 Hardware Information

173
- Firmware Description
  174
- Electrical Connections
  177
  - Serial Number Information
    178
  - Rear View of the Module
    178
- Interfaces
  179
  - Overview Interfaces
    180
- Setting the 8-Bit Configuration Switch
  184
  - Special Settings
    186
- Early Maintenance Feedback
  187
- Instrument Layout
  188
11 LAN Configuration

189
- What You Have to Do First
  190
- TCP/IP Parameter Configuration
  191
- Configuration Switch
  192
- Initialization Mode Selection
  193
- Dynamic Host Configuration Protocol (DHCP)
  197
  - General Information (DHCP)
    197
  - Setup (DHCP)
    198
- Link Configuration Selection
  200
- Automatic Configuration with Bootp
  201
- Manual Configuration
  211
  - With Telnet
    212
- PC and User Interface Software Setup Setup
  216
  - PC Setup for Local Configuration
    216
  - User Interface Software Setup
    217
12 Appendix

219
- General Safety Information
  220
  - Safety Standards
    220
  - General
    220
- Before Applying Power
  221
- Ground the Instrument
  221
- Do Not Modify the Instrument
  222
- Do Not Operate in an Explosive Atmosphere
  222
- Do Not Remove the Instrument Cover
  222
- In Case of Damage
  222
- Solvents
  223
- Safety Symbols
  224
- Waste Electrical and Electronic Equipment Directive
  226
- Radio Interference
  227
- Sound Emission
  228
- Agilent Technologies on Internet
  229

Agilent Technologies Categories

Measuring Instruments Laboratory Equipment Test Equipment Water Pump

Power Supply

More Agilent Technologies Manuals

Agilent Technologies G7104A Manuals

Agilent Technologies G7104A User Manual (310 pages)

Table of Contents

1 Introduction

Agilent 1260 Infinity II Flexible Pump

Agilent 1260 Infinity II Bio Flexible Pump

Operating Principle

Positions of the Multi Purpose Valve

Leak and Waste Handling

2 Site Requirements and Specifications

3 Using the Module

1260 Infinity II Flexible Pumps 65

4 Preparing the Pump

5 How to Optimize the Performance of Your Module

6 Troubleshooting and Diagnostics

7 Error Information

8 Maintenance

9 Parts and Materials for Maintenance

10 Identifying Cables

11 Hardware Information

12 LAN Configuration What You Have to Do First

13 Appendix

Agilent Technologies G7104A User Manual (234 pages)

Table of Contents

Table of Contents

1 Introduction

2 Site Requirements and Specifications

3 Using the Pump

4 How to Optimize the Performance of Your Module

6 Error Information

7 Maintenance

8 Parts and Materials

10 Hardware Information

11 LAN Configuration

12 Appendix

Related Products

Agilent Technologies Categories