beautypg.com
Manuals
Brands
TDK-Lambda Manuals
Power Supply
GEN150-34
TDK-Lambda GEN150-34 Manuals
Manuals and User Guides for TDK-Lambda GEN150-34. We have
1
TDK-Lambda GEN150-34 manual available for free PDF download: User Manual
TDK-Lambda GEN150-34 User Manual (82 pages)
Brand:
TDK-Lambda
| Category:
Power Supply
| Size: 3.98 MB
Table of Contents
Table of Contents
6
Chapter 1 General Information
16
Introduction
16
General Description
16
Models Covered
16
Features and Options
16
Multiple Output Power System
17
Control Via the Serial Communication Port
17
Analog Voltage Programming and Monitoring
17
Parallel Operation
17
Output Connections
17
Cooling and Mechanical Construction
18
Accessories
18
General
18
Serial Link Cable
18
Misc. Hardware
18
AC Cables
18
Chapter 2 Specifications
19
Output Rating
19
Input Characteristics
19
Constant Voltage Mode
19
Constant Current Mode
19
Analog Programming and Monitoring
19
Programming and Readback
20
Protective Functions
20
Front Panel
20
Environmental Conditions
20
Mechanical
20
Safety/Emc
20
Supplemental Characteristics
21
Outline Drawings
22
Chapter 3 Installation
23
General
23
Preparation for Use
23
Initial Inspection
23
Rack Mounting
23
To Install the Power Supply in a Rack
23
Ac Source Requirements
23
AC Input Connector
25
AC Input Cord
25
AC Input Wire Connection
25
Turn-On Checkout Procedure
26
General
26
Prior to Operation
26
Constant Voltage Check
27
Constant Current Check
27
OVP Check
27
UVL Check
27
Foldback Check
28
Address Setting
28
Baud Rate Setting
28
Connecting the Load
28
Load Wiring
28
Current Carrying Capacity
28
Noise and Impedance Effects
30
Inductive Loads
30
Making the Load Connections
30
Connecting Single Loads, Local Sensing (Default)
33
Connecting Single Loads, Remote Sensing
33
Connecting Multiple Loads, Radial Distribution Method
33
Multiple Loads Connection with Distribution Terminals
34
Grounding Outputs
34
Local and Remote Sensing
35
Local Sensing
35
Remote Sensing
36
J2 Sense Connector Technical Information
36
Repackaging for Shipment
36
Introduction
37
Front Panel Controls and Indicators
37
Rear Panel
39
Rear Panel Sw1 Setup Switch
40
SW1 Positions Functions
41
Resetting the Switch
41
Rear Panel J1 Programming and Monitoring Connector
42
Making J1 Connections
42
Chapter 5 Local Operation
44
Introduction
44
Standard Operation
44
Constant Voltage Mode
44
Constant Current Operation
44
Automatic Crossover
45
Over Voltage Protection (Ovp)
45
Setting the OVP Level
45
Activated OVP Protection Indications
45
Resetting the OVP Circuit
45
Under Voltage Limit (Uvl)
46
Setting the UVL Level
46
Foldback Protection
46
Setting the Foldback Protection
46
Resetting Activated Foldback Protection
46
Output On/Off Control
46
Output Shut-Off (So) Control Via Rear Panel J1 Connector
46
Enable/Disable Control Via Rear Panel J1 Connector
47
CV/CC Signal
47
Ps_Ok Signal
47
Safe Start and Auto-Restart Modes
48
Automatic Start Mode
48
Safe Start Mode
48
Over Temperature Protection (Otp)
48
Last Setting Memory
48
Series Operation
48
Series Connection for Increased Output Voltage
49
Series Connection for Positive and Negative Output Voltage
50
Parallel Operation
51
Daisy-Chain Connection
53
Front Panel Locking
53
Chapter 6 Remote Analog Programming
54
Introduction
54
Local/Remote Analog Controll
54
Local/Remote Analog Indication
54
Remote Voltage Programming of Output Voltage and Current Limit
55
Resistive Programming of Output Voltage and Current Limit
56
Remote Monitoring of Output Voltage and Current
57
Chapter 7 Rs232 & Rs485 Remote Control
58
Introduction
58
Configuration
58
Default Setting
58
Address Setting
58
RS232 or RS485 Selection
58
Baud Rate Setting
58
Setting the Unit into Remote or Local Mode
58
RS232/458 Port at Local Mode
59
Front Panel in Remote Mode
59
Rear Panel Rs232/485 Connector
59
Multi Power Supplies Connection to RS232 or RS485 Bus
61
Communication Interface Protocol
61
Data Format
61
Addressing
61
End of Message
61
Command Repeat
61
Checksum
61
Acknowledge
61
Error Message
62
Backspace
62
Error Messages
62
Command Set Description
62
General Guides
62
Command Set Categories
62
Initialization Control Commands
63
ID Control Commands
63
Output Control Commands
63
Global Output Commands
65
Status Control Commands
66
Status, Error and Srq Registers
67
General
67
Conditional Registers
67
Service Request: Enabled and Event Registers
68
Serial Communication Test Set-Up
71
Chapter 8 Isolated Analog Programming Option
72
Introduction
72
Specifications
72
Isolated Programming & Monitoring Connector
73
Setup and Operating Instructions
74
Setting up the Power Supply for 0-5/0-10V Isolated Programming and Monitoring
75
Parallel Operation with Isolated Analog Option
75
Chapter 9 Maintenance
76
Introduction
76
Units under Warranty
76
Periodic Maintenance
76
Adjustment and Calibration
76
Parts Replacement and Repairs
76
Troubleshooting
76
Fuse Rating
77
User Manual Index
81
Related Products
TDK-Lambda Genesys GEN150-10
TDK-Lambda Genesys GEN150-5
TDK-Lambda Genesys GEN150-16
TDK-LAMBDA GEN 150-22 ABCDE
TDK-Lambda Genesys GEN 1500W
TDK-Lambda Genesys GEN 15kW
TDK-Lambda Genesys GEN100-7.5
TDK-Lambda Genesys GEN12.5-60
TDK-Lambda Genesys GEN100-15
TDK-Lambda Genesys GEN10-240
TDK-Lambda Categories
Power Supply
Media Converter
Cables and connectors
Portable Generator
Network Hardware
More TDK-Lambda Manuals